Electrical circuit of a torch

Today we made an electrical circuit of a torch.

Below you will need to post your science report using the following subheadings:

  • Materials
  • Method
  • Results
  • Conclusion

16 thoughts on “Electrical circuit of a torch

  1. Materials
    Light blob, battery holder, wire, button
    Method
    I used the battery holder connected the wires put on the switch and hen clicked it and that is all.
    Results
    The light turned on with all of the tools.
    Conclusion
    How cold you make the light brighter and turn it on.

    1. Conclusion: If you added more battery’s the light would go really bright if there was no battery’s you could not turn on the light.

      Method: I had to connect the battery to the light bulb and I had to connect the light bulb to the switch.

  2. Materials
    Light Bulb
    Switch
    Wire
    Batteries
    Light Bulb Holders

    Method
    Connect one the wires off the batteries to the switch and the other wire to the light bulb.
    Then grab the extra wire and apply that to the other end of the light bulb.
    Sit and be amazed by the bright light.

    Results
    When we connected the wires to all of the parts the light was lighten up but a little weak. So we applied more batteries to the light to make it look brighter. We then applied another battery because it was still too dull but after applying the third battery it was incredibly bright. We then also added another light which then required even more batteries to make it brighter.

    Conclusion
    This happened because the electrons from the acid filled battery travelled through the light and lit up the bulb. When we pushed the switch the light went out.

  3. ~Materials~

    ~Battery & Holder
    ~Switch
    ~Wires
    ~ Light and Holder
    ~Blu Tack

    ~Method~

    1~ Place battery in holder
    2~ Tie black wire to the red wire
    3~ Tie the red wire to the switch
    4~ Tie the black big wire to the Switch
    5~ Tie the big black wire to the Light and Holder
    6~ Place Blu tack on top of the light holders where the switch is.

    ~Results~

    The light had turnt on after we followed all of the steps and we added out Blu tack with out the Blu tack It wouldn’t have stayed in place.

    ~Conclusion~

    Our Eletcric circuit worked perfectly, the light came on and off as Me and Joardan pressed the switch as you add more battreys the brighter the light gets.

    How could you make the light brighter?
    Add more of the battery and add more light globes to make more light.

    What is needed to make eletcricty?
    ~Battery & Holder
    ~Switch
    ~Wires
    ~ Light and Holder
    ~Blu Tack
    ~ Lots of wires

  4. Materials
    🔋Battery
    Battery holder
    Light
    Light holder
    Wire

    Method
    Step 1
    Put the battery on the battery holder
    Step2
    Put the light in the light holder
    Step3
    Connect all the wire to the battery
    Step4
    Connects the wires to the switch

    Results
    When all the wires where connected to the battery and switch the light Went on.

    Conclusion
    By connecting more battery that how it make the light brighter.
    They Bren the coil to make electricity.

  5. 🔦Materials💡
    🔋Battery
    Wire
    Battery holder
    Switch
    💡Light
    💡Light holder

    Method
    Step.1⃣ Put the battery in the battery holder.
    Step.2⃣ Connect all the wires to the holder and switch.
    Step.3⃣ Put the light in the light holder.
    Step.4⃣ Connect the wire to the switch.
    Results
    When it was all connected the light was working. When Tristan and Doyle did it with three battery’s it was really bright compered to ours.

    Conclusion

    You could make the light brighter by using more battery’s. To make electricity you need to use the heat of the cole.

  6. 1. Battery
    2. Cord
    3. Switch
    4. Light ball holder
    5. Battery holder

    Connect the wire to the switch connect the wire to the light ball connect the wire to light ball holder and the battery to the battery holder.

    When I connected the wire to the switch andut the wire on cord and that mean I could switch the light ball on and off.

    You can the light brighter you can use more battery’s and connect the to the battery.

    Burnt cole.

  7. Science (Electrical Circuits)
    Materials
    Wire
    Torch
    Light glob
    Light holder
    Switch
    Battery

    Method
    First we but the battery in the torch then we put the two black wires together one end of the wire to the switch then put the red wire on the light and the end of the black wire then the light blob switch on.

    Results
    The glob switch on to make light in the room.

    Conclusion
    You could make the light brighter is with three battery’s
    All you need was a battery to make it all work

  8. Materials
    Batteries
    Wire
    Bulb
    Switch
    Bulb holder

    Method
    1. Connect one wire from battery to switch and the other wire to bulb.
    2.Then grab the other wire and apply it to the other of the bulb and switch.
    3. Stand back and watch.

    Results
    When we connected the wires to all of the parts the light was lighten up but a little weak. So we applied more batteries to the light to make it look brighter. We then applied another battery because it was still too dark but after applying the third battery it was really bright. We then also added another light which then even more batteries we’re need to make it brighter.

    Conclusion
    We made the lights brighter by adding more batteries. We need electric energy stored in batteries.

  9. Materials- 1.Battery
    2. Battery holder
    3.Light
    4. Wire
    5. Switch
    6. Switch holder
    7. Glue tack

    Method- 1. We had to put the battery in the battery holder.
    2. Then we had to connect the wire’s to the light.
    3. We also had to stick glue tack on the wire thing to keep it connected.

    Results- Mine and Ethan’s did not work because it was harder for us with out the medal thing to keep the wire on.

    Conclusion- I think we could of made the light brighter if we had more battery’s and more wire. You need to use wire and battery to have electricity.

  10. Materials
    We use 1 1.5V battery and I light bulb 1 switch 2wires red and a black wire and a battery holder and some blu-tack.

    Method
    1. We put the battery in the battery holder.

    2. We got our switch and connected one of the wire in the ofter wire.

    3. We connected the other end of the wire and the other end of the battery holder wire.

    4 we stuck the two wires with blu-tack on the light holder.

    Results
    The light worked because we were taking power from the battery and then it traveled to the light bulb

    Conclusion
    We could of made the light brighter by getting more battery’s so it gets more power out.
    Or you could get a bigger battery.

    You need wire and a battery and a light

  11. ELECTRICAL CIRCUITS

    Materials
    The materials we use were 1 1.5V battery, 1 lightbulb, 1 switch, 2 wires (Red and Black), 1 battery holder and some Blu-Tack

    Method
    1. We put the battery in the battery holder.
    2. We got our switch and we connected 1 of the battery holder wires and 1 of the spare wires.
    3. We connected the other end of the spare wire and we thread in through the holes which was connected to the lightbulb holder and placed the lightbulb in the holder.
    4. We stuck the 2 ends of the wires to the bottom of the lightbulb holder with some Blu-Tack.
    5. Our lightbulb had lit up because the Electrons were moving very fast to keep the lightbulb running with power but it wasn’t very bright and that didn’t really matter.

    Results
    The Electrons travelled from the negative side of the battery, through the wire, to the bottom of the lightbulb holder, through to the lightbulb which created power.

    Conclusion
    How could we make the lightbulb shine brighter?
    We could’ve added more batteries and wires and connect them to the bottom of the lightbulb.

    What is needed to make electricity?
    The thing that are needed to created electricity are wires, lightbulbs, batteries and battery holders.

    By: Mahnee

  12. Materials:

    1) A light bob.
    2) A battery.
    3) Two wires.
    3) A battery holder
    4) A light bob holder.

    Method:

    1) put the battery in the battery holder.
    2) put the wire connected to the battery.
    3) connect to the light bob.
    4) put the passer to connect on the wire.
    5) connect everything together.
    6) press the switch and the light bob will go on.

    Results:

    There was all these bits and piece all over the table what we had to put together in partners. Lusanda and I we connect the two wires to the battery and connected to the light switch. We need to put the baser together to make go off and on.

    Conclusion:

    To make it brighter you need to put more and more batter.

    To make electricity you need a battery.

  13. Materials
    Wire, light blob, battery, switch and the battery holder

    Method
    Connect the wire to the battery, than connect to the light, than to the buzzer and than the battery.
    Results
    The light went on and and the buzzer turned it off.
    Conclusion

    How could you make it brighter: add more battery to the light

    What is needed to make electricity:
    It is a lot of electricity in it.

  14. Materials.The materials where light blobe battery wire swich battery holder.
    Method.Put the battery in the battery holder conect the wire to the battery make sure the swich is coneted to the wire
    Results it didn’t work the first because the swich was conected but then we conected it and it worked
    Conclusion to make the light brighter you had to add more battery’s
    You need power to make electricity.

  15. 💡Materials🔋
    Light bulb
    Battery holder
    Battery
    Wires
    Switch

    ||Method||
    Using the battery in the battery holder to connect one side of the wire to the switch and the different wire we got to the other side of the switch and connecting the other end of the battery and the switch to the light bulb metal.

    ||Results||
    The light bulb worked without Max and I didn’t touch the wires after we have completed.

    ||Conclusion||
    You can make the light brighter with more wires and battery’s.

    You have to have 2 wires and battery and battery holder with light bulb.

Leave a Reply to hayleys3931 Cancel reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s